 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Internationally Approved Toggles Series P Distinctive Characteristics International certifications from UL, CSA, VDE, SEMKO, and SEV. High torque bushing construction prevents rotation or separation from frame during installation. Stainless steel frame resists corrosion and increases environmental safety. Case/base of heat resistant resin meets UL94V-0 flammability standard. Contacts of special silver alloy resist arcing and guarantee stable electrical contact and long life. High insulating barriers increase isolation of circuits in double pole devices and provide added protection to contact points. Prominent external insulating barriers increase insulation resistance and dielectric strength. Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. Clinching of the frame to the case well above the base and terminals provides 4,000V dielectric strength. Actual Size NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Toggles Series P General Specifications Electrical Capacity Resistive Load: Motor Load: Lamp Load: 10A @ 125V AC or 6A @ 250V AC 400W @ 125V AC 2A @ 125V AC for On-Off-On circuit & 3A @ 125V AC for other circuits Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 100,000 operations minimum 25,000 operations minimum 25 Materials & Finishes Toggle Cap: Lever: Bushing: Frame: Case/Base: Movable Contacts: Stationary Contacts: Terminals: Brass with nickel plating Brass with chrome plating Brass with nickel plating Stainless steel Diallyl phthalate resin (UL94V-0) Silver alloy with silver plating Pure silver with silver plating Copper with silver plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: -10C through +85C (+14F through +185F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Soldering Time & Temp: Wave Soldering Recommended (Straight PC): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL Recognized: C-UL Recognized: R CSA Certified: V DE VDE Approved: SEMKO Approved: SEV Approved: UL94V-0 rated case/base All models recognized at 10A @ 125V AC & 6A @ 250V AC; UL File No. WOYR2.E44145. Add "/U" to end of part number to order UL mark on switch. All models recognized at 10A @ 125V AC & 6A @ 250V AC; C-UL File No. WOYR8.E44145. Add "/C-UL" to end of part number to order C-UL mark on switch. All models certified at 10A @ 125V AC & 6A @ 250V AC; CSA File No. 023535-0-000. Add "/C" to end of part number to order CSA mark on switch. All models approved at 10A @ 125V AC & 6A @ 250V AC; License No. 119174. Marking on switch is standard. P2011, P2012, P2013, P2021, P2022 models approved at 10A @ 125V AC & 6A @ 125/250V AC; Reference No. 9915205/01-02. Marking on switch is standard. All models with Quick Connect Terminals approved at 10A @ 125V AC & 6A @ 125/250V AC; (P2013 for micro-switch only); Authorization No. 02.0466. Marking on switch is standard. NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Toggles TYPICAL SWITCH ORDERING EXAMPLE Series P P20 POLES & CIRCUITS 11 12 13 21 22 23 SPST SPDT SPDT DPST DPDT DPDT ON ON ON ON ON ON NONE NONE OFF NONE NONE OFF OFF ON ON OFF ON ON 22 No Code E B D B TERMINALS No Code P Z Solder Lug Straight PC .187" (4.75mm) Quick Connect .512" (13.0mm) White Cap with 6mm Bushing .450" (11.4mm) Flatted with 6mm Bushing .689" (17.5mm) Large Bat with 12mm Bushing .748" (19.0mm) White Capped Column with 12mm Bushing TOGGLES & BUSHINGS DESCRIPTION FOR TYPICAL ORDERING EXAMPLE P2022B .689" (17.5mm) Large Bat with 12mm Bushing DPDT ON-NONE-ON Circuit Solder Lug Terminals IMPORTANT: VDE, SEMKO & SEV are marked on approved models. Switches are supplied without UL, C-UL & CSA marking unless specified. Specific models & ratings noted on General Specifications page. POLES & CIRCUITS Toggle Position Down Pole Model Keyway Connected Terminals Up Down Keyway Throw & Schematics Up Note: Terminal numbers are on the switch. 1 (COM) Center Center SP P2011 P2012 P2013 P2021 P2022 P2023 ON ON ON ON ON ON NONE NONE OFF NONE NONE OFF OFF ON ON OFF ON ON 1-1b OPEN OPEN SPST 1b 1 (COM) 1a 1 (COM) 1b 1 1a (COM) 1b 2a 2 2b 2 2b 1b SP 1-1b OPEN 1-1a SPDT DP 1-1b 2-2b OPEN OPEN DPST DP 1-1b 2-2b OPEN 1-1a 2-2a DPDT NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Toggles TOGGLES & BUSHINGS No Code .512" (13.0mm) White Cap with 6mm Bushing 25 (2.54) .100 (11.4) .450 Series P .748" (19.0mm) White Capped Column with 12mm Bushing (4.4) Dia .173 25 E .450" (11.4mm) Flatted with 6mm Bushing 25 (5.08) .200 B .689" (17.5mm) Large Bat with 12mm Bushing 25 (6.0) Dia .236 (17.5) .689 D (4.2) Dia .165 (13.0) .512 (19.0) .748 Panel Cutouts Panel Thickness with Keyway .134" (3.4mm) maximum (5.6) .220 (6.35) Dia .250 (0.6) .024 Panel Thickness with Locking Ring .102" (2.6mm) maximum (6.35) Dia .250 (6.5) .256 (2.2) Dia .087 Panel Thickness with Keyway .256" (6.5mm) maximum (12.5) Dia .492 (11.5) .453 (1.5) .060 Panel Thickness with Locking Ring .217" (5.5mm) maximum (12.5) Dia .492 (9.0) .354 (3.0) Dia .118 Standard Hardware For 6mm Bushing: 1 Locking Ring AT507M, 1 Internal Tooth Lockwasher AT509, 2 Hex Nuts AT513M For 12mm Bushing: 1 Hex Face Nut AT503M, 1 Locking Ring AT506M, 1 Internal Tooth Lockwasher AT508, 1 Hex Mounting Nut AT527M TERMINALS No Code Epoxy Seal Solder Lug (2.6) .102 (2.0) (4.5) .079 .177 (1.25) .049 Thk = (1.0) .039 1b Z .187" (4.75mm) Quick Connect (6.35) .250 (1.3) Dia .051 (9.0) .354 (4.75) .187 Thk = (0.8) .031 2b 1b P Epoxy Seal Straight PC (7.6) .299 (1.17) .046 Thk = (1.0) .039 1b 2b 1b (4.8) .189 SPST 1 (7.62) Typ .300 (1.8) Dia Typ .071 SPDT 1 (7.62) Typ .300 DPST 2 1 (7.62) Typ .300 (1.8) Dia Typ .071 DPDT 2 1 (7.62) Typ .300 1a (1.8) Dia Typ .071 (10.16) .400 2a 1a (10.16) .400 (1.8) Dia Typ .071 TYPICAL SWITCH DIMENSIONS 6mm Bushing Keyway M6 P0.75 P2011, P2012, P2013 (1.25) x (2.0) Typ .049 x .079 (1.0) Typ .039 1b 25 (0.8) .031 (7.62) .300 (0.5) .020 1 (20.5) .807 (4.2) Dia .165 (11.0) .433 (13.0) .512 1a (0.9) .035 (8.0) .315 (22.0) .866 (5.0) .197 (2.6) .102 P2012 P2011 models do not have terminal 1a. 12mm Bushing Keyway P2021B, P2022B, P2023B M12 P1 (1.25) x (2.0) Typ .049 x .079 (1.0) Typ .039 2b 1b 25 (0.8) .031 (7.62) .300 (0.5) .020 2 1 (20.5) .807 2a 1a (20.0) .787 (6.0) Dia .236 (17.5) .689 (12.0) .472 (21.1) .831 (5.0) .197 (10.16) .400 (2.6) Typ .102 P2022B P2021 models do not have terminals 1a & 2a. 03-07 NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com |
Price & Availability of P2013DP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |